Yale SmartHome Alarm series Specifiche Scaricare il pdf (Pagina 15)

second increments.

•30secondsisthefactorydefault.

Entry Sound

The control unit will beep during the entry delay

period as an entry warning, you can switch the

sound on and off with this setting.

•Entrysoundonisthefactorydefault.

Exit Sound

The control unit will beep during the exit delay period

as an exit warning, you can switch the sound on and

off with this setting.

•Exitsoundonisthefactorydefault.

Door Chime

Any door contact or PIR set to entry will cause

the control unit to chime when activated when the

system is disarmed. This is used to signal when

anyone has entered your premises. You can switch

the sound on and off with this setting.

•Chimeoffisthefactorydefault.

DC Open/Close

If this is turned On, the control panel will sound a

door chime and display a fault message when user

tries to arm the system with Door contact opened.

•DCOpen/CloseOffisthefactorydefault.

LCD Backlight

The control unit display LCD can be turned on

Permanently or set to auto turn off after 30 seconds

of last key pressed.

•Autooffisthefactorydefault.

Key Tone

The control unit can be made to beep when a key is

pressed. Key Tone can be selected to On or Off.

•KeyToneOnisthefactorydefault.

Ring Tone

The control unit can be made to beep when the

phone is ringing, you can switch the sound on and

off with this setting.

•Ringingoffisthefactorydefault.

Alarm Length

The siren (both external and built-in) will sound when

an alarm is activated. The length of the alarm can be

set from 1 to 10 minutes in 1 minute increments with

this setting.

•3minutesisthefactorydefault.

C.U. Siren

You can disable the control unit’s built-in siren with

this setting.

•Sirenonisthefactorydefault.

Jamming Det

Enable or disable Jamming/Interference detection on

the control panel. Conﬁrmed by pressing the 3 key.

Default setting is Disable (recommended).

KF Entry

When selected as Off, user must ﬁrst trigger an entry

sensor before the keyfob can disable the system.

Please select On if you which to disarm the system

without ﬁrst triggering an entry sensor.

•KFEntryOffisthefactorydefault.

•IftheKeyfob’sPanicbuttonistriggered,the

same keyfob cannot be use for disarming the siren.

Tamper Alarm

If set to Away Arm only, it will trigger the alarm when

tamper is active under away arm mode (also known

as full arm). It will only give a fault LED indication in

all other mode. If set to Normal, a tamper condition

will always triggers a burglar alarm under disarm,

home arm and away arm mode.

•AwayArmOnlyisthefactorydefault.

Mobility CHK (for elderly or inﬁrm)

If there is no movement around the house for a

preset period of time (from home omit sensors under

part arm and all sensors under disarm mode), an

emergency alarm will be activated and reported over

the telephone line. Any key presses on the panel

and entry sensor triggering will reset the countdown

timer. The monitoring can be disabled or set at 4, 8

and 12 hour.

•Disableisthefactorydefault.

Siren Delay

This setting allows a delay before the control unit

and external sirens are activated. You might want to

use this if you do not want the control unit to draw

attention to itself during an alarm, to give it time to

dial out on the telephone line. The delay can be set

from Disable (no delay) to 10 minutes in increments

of 1 minute.

•Disableisthefactorydefault.

Warning Beep

The control unit will give a reminder beep every 30

seconds in the event of a system fault, such as

tamper or a low battery etc. This setting allows this

feature to be switched on and off.

1 2 ... 10 11 12 13 14 15 16 17 18 19 20 ... 31 32

Commenti su questo manuale

Nessun commento

Yale SmartHome Alarm series Specifiche Pagina 15

Commenti su questo manuale

Prodotti e manuali riguardandi Sistemi di controllo di accesso Yale SmartHome Alarm series